Wax bur, parallel, round faceThe wax bur F1373W23 features a rounded face cut – perfectly suitable for preparing precise ditches in the marginal area. |
Tungsten carbide
f 2.35 mm short. F1372W07 F1372W10 F1372W15 F1372W23 |
Tungsten carbide
f 3.00 mm short. F1373W07 F1373W10 F1373W15 F1373W23 |
Profile bur, parallel, round faceThe round face cut of the profile bur F1373H23 corresponds to the face cut of the wax bur shown above. Precisely designed ditches in wax can be milled additionally and easily with the suitable profile bur. |
Tungsten carbide
f 2.35 mm short. F1372H07 F1372H10 F1372H15 F1372H23 |
Tungsten carbide
f 3.00 mm short. F1373H07 F1373H10 F1373H15 F1373H23 |
Polishing bur, parallel, round faceA mirror-finish is prepared with the polishing bur F1373P23. The identical face cuts of all wax, profile and polishing burs of the same size, simplify designing a perfect marginal ditch. |
Tungsten carbide
f 2.35 mm short F1372P07 F1372P10 F1372P15 F1372P23 |
Tungsten carbide
f 3.0 mm short F1373P07 F1373P10 F1373P15 F1373P23 |
Wax bur, conical, round facePreparation of a tapered crown with marginal ditch. The F2003W40 features are rounded face. A wax pattern is first prepared with this wax bur, the rounded face features a sharp cutting edge and produces a precise ditch. |
Tungsten carbide
f 2.35 mm short F2002W23 F2002W31 F2002W40 |
Tungsten carbide
f 3.00 mm short F2003W23 F2003W31 F2003W40 |
Profile bur, conical, round faceThe object is shaped with the profile bur after casting. The radius of the face cut has been precisely matched with the corresponding wax bur. The ditch can then be shaped quickly. |
Tungsten carbide f 2.35 mm short
F2002H23 F2002H31 F2002H40 |
Tungsten carbide f 3.00 mm short
F2003H23 F2003H31 F2003H40 |
Polishing bur, conical, round faceAfter contouring, the surface is finished with the polishing bur, slight reworking with this bur obtains a high lustre polishing even in the area of the ditch, since the radii of the polishing, profile and wax burs are absolutely identical. |
Tungsten carbide f 2.35 mm short
F2002P23 F2002P31 F2002P40 |
Tungsten carbide f 3.00 mm short
F2003P23 F2003P31 F2003P40 |
Groove BurThe groove vut F5383H10 exclusively serves to prepare groves. For this purpose the groove bur is only moved up and down in the ertical axis. The curt on the ace simplifies extending the grooves to the cervical direction. At speeds of 15,000 – 20,000 rpm a fine cutting performance and a mirror-like high lustre on the milling surface can be obtained. |
Tungsten carbide f 2.35 mm short
F5382H07 F5382H10 F5382H12 F5382H15 F5382H20 |
Tungsten carbide f 3.00 mm short
F5383H07 F5383H10 F5383H12 F5383H15 F5383H20 |
Shoulder burThe occlusal shoulder is prepared with a special shoulder bur. This bur features a face cut which smoothes the bottom of the shoulder. Optimum use of this tool is ensured at speeds of approximately 15,000 -20,000 rpm. A mirror-like surface is achieved with the relief cut. Additional polishing is not required. |
Tungsten carbide f 2.35 mm short
F2052H27 F2052H29 |
Tungsten carbide f 3.00 mm short
F2053H27 F2053H29 |